I already think it's more than good enough for FSX. Just FYI, I think that the upper cowl flaps are controlled separately. I watched the official training for this plane many times, as it was a very fun one. And they always said to "keep the upper cowl flaps closed", except during taxi. I can find the link for you, if you want.
-
There seems to be an up tick in Political commentary in recent months. Those of us who are long time members of the site we know that Political and Religious content has been banned for years. Nothing has changed. Please leave all political and religiours commentary out of the fourms.
If you recently joined the forums you were not presented with this restriction in the terms of service. This was due to a conversion error when we went from vBulletin to Xenforo. We have updated our terms of service to reflect these corrections.
Please note any post refering to a politicion will be considered political even if it is intended to be humor. Our experience is these topics have a way of dividing the forums and causing deep resentment amoung members. It is a poison to the community. We apprciate compliance with the rules.
The Staff of SOH
Douglas A20 Havoc
- Thread starter Milton Shupe
- Start date
I already think it's more than good enough for FSX. Just FYI, I think that the upper cowl flaps are controlled separately. I watched the official training for this plane many times, as it was a very fun one. And they always said to "keep the upper cowl flaps closed", except during taxi. I can find the link for you, if you want.
Thanks for that reminder; I have that link as well. Will watch again when its time.
No, just me at the moment; that is typical until I get the exterior model done and mapped and in the sim properly.
I just created a test folder this afternoon and did my first export to check it in the sim. It looked pretty good and all but one animation worked correctly, now fixed.
I usually don't do a model specific flight model until I have all the appropriate parts in place; hopefully that will be in the next few days.
Then I usually take a break from modeling and start the flight model. I normally use either Airwrench or the FDWB to do the first few cuts on the FM and tweak from there. If I'm really busy and Tom Falley volunteers, I send it all to him after mapping for textures.
However, you you want to give it a go, I would be happy for you to jump in.
Attachments
Let me see what I can come up with here.
My first cut would be to take a Lodestar aircraft config file and modify as many parameters as I can find to fitthe A-20. If I can get the Lodestar to A-20 specs, I'll modify appropriate values in the .air file.
Here is one thing - I only have FSX Acceleration installed; no FS2004. Do you see any problems with that ??
My first cut would be to take a Lodestar aircraft config file and modify as many parameters as I can find to fitthe A-20. If I can get the Lodestar to A-20 specs, I'll modify appropriate values in the .air file.
Here is one thing - I only have FSX Acceleration installed; no FS2004. Do you see any problems with that ??
Last edited:
Now this is interesting:
http://www.enginehistory.org/Wright/R-2600/R-2600CaseHx.shtml
"Cylinder Rust and Corrosion
The most vexing problem was rust and corrosion in the cylinders. The Corrosion
Committee, established by CTI-1325 (May 17, 1943) wrote, "We do not know the answer but
are beginning to suspect Gremlins." The FBI checked for sabotage. The "epidemic" of
December 1942 to March 1943 was corrosion, and that of June-July 1943, rust.
............
Pratt & Whitney blamed moisture applied to steel parts during engine assembly by
ungloved hands."
http://www.enginehistory.org/Wright/R-2600/R-2600CaseHx.shtml
"Cylinder Rust and Corrosion
The most vexing problem was rust and corrosion in the cylinders. The Corrosion
Committee, established by CTI-1325 (May 17, 1943) wrote, "We do not know the answer but
are beginning to suspect Gremlins." The FBI checked for sabotage. The "epidemic" of
December 1942 to March 1943 was corrosion, and that of June-July 1943, rust.
............
Pratt & Whitney blamed moisture applied to steel parts during engine assembly by
ungloved hands."
Last edited by a moderator:
lemonadedrinker
Charter Member
Hi,
Nothing much was learned in the intervening years, as the beautiful little Alfasud was destroyed by rust/corrosion from untrained hands in their new factory in the south of Italy.
Andy.
Nothing much was learned in the intervening years, as the beautiful little Alfasud was destroyed by rust/corrosion from untrained hands in their new factory in the south of Italy.
Andy.
Hi Tom; great to see you here.
I appreciate that.
Working on the nose gear now; about done, and moving on to main gear today. Once that is in place, we will have something to test in the sim. Progress, slowly by surely.
When you call this progress slow, I really wonder what you consider fast. I assume that's close to instant ready
The Airfix Boston was one of the more affordable larger model kits. I loved it and have built several..... Soonish I will fly one!
Cheers,
Huub
Huub, thank you; yes, I have had limited time, or rather lots of daily distractions, trying to get this exterior model assembled. I do my best work when I can stay focused on the task at hand and let it flow.
I too like the early models of the A-20 and will be doing the several variants.
Milton:
I have the A20_draft_2.pdf file and the two drawings from the American Aircraft Modeller (L&R) November 1970 issue. I am now ready to start placing crew loads, engine locations, gear positions into an aircraft.cfg file.
What I need to know is where you have placed the C.G. reference point -- how many feet + inches behind the leading edge of the wing. I assume you have bisected the fuselage in side and top view for your other "0.0" coordinate points.
I have the A20_draft_2.pdf file and the two drawings from the American Aircraft Modeller (L&R) November 1970 issue. I am now ready to start placing crew loads, engine locations, gear positions into an aircraft.cfg file.
What I need to know is where you have placed the C.G. reference point -- how many feet + inches behind the leading edge of the wing. I assume you have bisected the fuselage in side and top view for your other "0.0" coordinate points.
