There seems to be an uptick in Political comments in recent months. Those of us who are long time members of the site know that Political and Religious content has been banned for years. Nothing has changed. Please leave all political and religious comments out of the forums.
If you recently joined the forums you were not presented with this restriction in the terms of service. This was due to a conversion error when we went from vBulletin to Xenforo. We have updated our terms of service to reflect these corrections.
Please note any post refering to a politician will be considered political even if it is intended to be humor. Our experience is these topics have a way of dividing the forums and causing deep resentment among members. It is a poison to the community. We appreciate compliance with the rules.
The Staff of SOH
Ignore my above post..too late to edit it.
Thanks but I don't have shockwave lights so the above wouldn't work. I did manage to get the lights to work but now there is too many and I can't turn the top red beacon off as well as the belly, they are on all the time. I used this from page 15.
[LIGHTS]
Types: 1=beacon, 2=strobe, 3=navigation, 4=cockpit, 5=landing, 6=Taxi, 7=Recognition, 8=?, 9=Logo, 10=?
light.0= 9, 35.27, 0.70, -1.6, //P-3landing Nose
light.1= 9, 35.27, -0.70, -1.6, //P-3landing Nose
light.2= 7, 1.30, -24.00, -1.0, //P-3landing Wing
light.3= 7, 1.30, 24.00, -1.0, //P-3landing Wing
light.4= 7, -2.30, -24.00, -1.0, //P-3landing Wing
light.5= 7, -2.30, 24.00, -1.0, //P-3landing Wing
light.6= 4, 31.27, 0.00, 5.870, fx_vclight_p3, //VC Lighting
light.7=3, -0.2, -52.00, 4.3, fx_navredh , //Port Nav
light.8=3, -0.2, 52.00, 4.3, fx_navgreh, //Stbd Nav
light.9=2, -0.2, -52.00, 4.3, fx_strobeh, //Port Strobe
light.10=2, -0.2, 52.00, 4.3, fx_strobeh, //Stbd Strobe
light.11=1, -17.0, 0.00, -2.0, fx_beaconh , //Belly Beacon
light.12=2, -17.0, 0.00, -1.6, fx_strobeh , //Belly Strobe
light.13=1, -20.5, 0.00, 10.5, fx_beaconh , //Upper Beacon
light.14=2, -20.5, 0.00, 10.1, fx_strobeh , //Upper Strobe
light.15=3, -59.44, 0.00, 8.9, fx_navwhi , //Upper Tail Pos Light
light.16=3, -53.80, 0.00, 3.2, fx_navwhi , //Lower Tail Pos Light
light.17=7, -59.44, 0.00, 8.9, fx_recog , //Upper Tail Recgn Light
light.18=7, -53.80, 0.00, 3.2, fx_recog , //Lower Tail Recgn Light
No smoke either. Tried every possible config I could find in this thread as well as two zip files.
My P-3 install must really have problems then, because I do have the CS130, and the smoke effect is not working![]()
Got my smoke effect working. Had to edit my aircraft.cfg file, but all is well now. Thanks. NC
if there any way to correct the engine start order. how do u stop single engine on taxi eg normally taxi under two engines.
I have a few RAAF repaints that a friend sent to me .. AussieMan now has these in his grip.
any chance of anymore fictional RAF repaints please.
Hi Andy, good to see I was able to get your problem finally sorted.
There is a version 3.2 in the Warbirds Library here on the SOH.
As for the correct engine start on the version I have installed there are 4 switches on the console between the pilots at the top near the throttles. Click each one of those and you can start the engines. The switch nearest to the pilot is #1 engine. The normal start procedure is 4, 3, 2, 1. I found that to shut down the engines you need to click the switches again.
I have had a look at the RAAF paints and they look really good mate. I cannot see anything wrong at the moment but will spend more time looking at them today.
This is not DX10 compatible right? Got texture issues in DX10.
Here is the WIP beta P-3C BMUP from Bupers SDC Dallas ("NAWCS-23") repaint. I appreciate if the people here on the forum with USN Orion knowledge can look her over.
As already mentioned, this is a rather secretive unit and all serials and decals beside standard danger/warning stencils and the US insignia have been removed. Among many things, this unit was sort of the lab to create the LSRS system working in close cooperation with Boeing, Raytheon and L3.
This is not DX10 compatible right? Got texture issues in DX10.