• There seems to be an uptick in Political comments in recent months. Those of us who are long time members of the site know that Political and Religious content has been banned for years. Nothing has changed. Please leave all political and religious comments out of the forums.

    If you recently joined the forums you were not presented with this restriction in the terms of service. This was due to a conversion error when we went from vBulletin to Xenforo. We have updated our terms of service to reflect these corrections.

    Please note any post refering to a politician will be considered political even if it is intended to be humor. Our experience is these topics have a way of dividing the forums and causing deep resentment among members. It is a poison to the community. We appreciate compliance with the rules.

    The Staff of SOH

  • Server side Maintenance is done. We still have an update to the forum software to run but that one will have to wait for a better time.

INITIAL RELEASE: Grumman Goose G21A Redux II

Against the wind

dTv3tlW.jpg
 
So I restarted from scratch, after I found something that worked...up to this point I was just making destructive adjustments to the .dds files. So this morning I remade them into PSDs using the .dds files and then added adjustment layers etc. to get back to the look I was going for. In the process I discovered that there are significant of what looks like errors in the 3D mesh of the model?? Looks like there may be numerous places where the maybe the vertices are inverted? You can tell this is so, from the way the reflections seem to randomly become inverted to the direction they should be going. It's not readily apparent with non-metallic textured surfaces. Although the dark areas on the inboard trailing edges of the wings is noticeable from most paints. Not sure if this can be fixed? At any rate. It's very noticeable from certain lighting angles and not from others. As would be expected. Outside of that, it's coming along nicely! Below are some screens from various lighting conditions.

Microsoft_Flight_Simulator_Screenshot_2021.01.04_-_00.10.53.59.png


Microsoft_Flight_Simulator_Screenshot_2021.01.04_-_00.12.09.47.png


Microsoft_Flight_Simulator_Screenshot_2021.01.04_-_00.17.47.37.png


Microsoft_Flight_Simulator_Screenshot_2021.01.04_-_09.34.51.87.png


Microsoft_Flight_Simulator_Screenshot_2021.01.04_-_09.38.38.41.png
 
000rick000 said:
So I restarted from scratch, after I found something that worked...up to this point I was just making destructive adjustments to the .dds files. So this morning I remade them into PSDs using the .dds files and then added adjustment layers etc. to get back to the look I was going for. In the process I discovered that there are significant of what looks like errors in the 3D mesh of the model?? Looks like there may be numerous places where the maybe the vertices are inverted? You can tell this is so, from the way the reflections seem to randomly become inverted to the direction they should be going. It's not readily apparent with non-metallic textured surfaces. Although the dark areas on the inboard trailing edges of the wings is noticeable from most paints. Not sure if this can be fixed?
Click to expand...

Wow, that is quite noticeable! It does indeed seem as if something is up (or down?! LOL) with quite a few vertices. Maybe worth importing into ModelConverterX (and onwards into Blender) to take a closer look at what might be happening?

In fact once pointed out it is very difficult to "unsee" it! For instance I can now also see the same artifacts in Jan's screenshots of his repaints.
 
Hopefully it's the Normals then. But it really looks like inversion along the polygons of the mesh. It's mirrored on both sides. with every part you can see.

unknown.png


unknown.png


unknown.png


unknown.png


unknown.png
 
I just looked at the Normals for the A1 Texture, and there does not appear to be any strange lines going through the wings at least.
 
If it were FSX/P3D i'd look for different smoothing groups caused by unwelded vertices ?
 
Hi
When applying "Alaska" texture you have to exe "auto_json" to modify "layout.json". Downloaded several te4xture that I intend to use. Think that when I use "auto_json" I´m just adding a line to "layout.json, not replacing something. Is this correct? Is it right to run auto.json everytime I add a texture? Think so, want to make sure...
And when I want to remove an installed texture should I change something on "layout.json" or, as usual, just in aircraft.cfg?
BTW-why every time I start MSFS weather is set in Snow? Wherever I go? Tried to change it by ticking "save as" near the "snow window" to no avail, snowing every time, have to stop and change manually. Anyone else?
Thanks, stay safe, bad here in Portugal...
 
Loving the Goose so far, using it to fly the Imperial Airways route from England to Australia and currently somewhere over the Med...

Few things I've noticed.

BUG REPORT
Issue Experienced: Autopilot heading bug is consistently ~3 degrees right of where the autopilot flies.
Expected Behaviour: Autopilot should hold the heading set.
Steps to Reproduce: In flight set heading bug, engage autopilot, select HDG mode.

attachment.php


BUG REPORT
Issue Experienced: Cockpit side window doesn't meet the framing on the lower edge.
Expected Behaviour: Should fill window.
Steps to Reproduce: View exterior of aircraft.
attachment.php


BUG REPORT
Issue Experienced: Right hand float switch not animated.
Expected Behaviour: Switch should move when clicked as the left hand one does.
Steps to Reproduce: Cycle float switches.

attachment.php


Nothing major and I'm sure you're already aware of it.
 

Attachments

  • Autopilot HDG Bug.jpg
    Autopilot HDG Bug.jpg
    78.2 KB · Views: 402
  • Goose Window.jpg
    Goose Window.jpg
    32.2 KB · Views: 398
  • Float Switches.jpg
    Float Switches.jpg
    56.5 KB · Views: 399
SkippyBing said:
Loving the Goose so far, using it to fly the Imperial Airways route from England to Australia and currently somewhere over the Med...

Few things I've noticed.

BUG REPORT
Issue Experienced: Autopilot heading bug is consistently ~3 degrees right of where the autopilot flies.
Expected Behaviour: Autopilot should hold the heading set.
Steps to Reproduce: In flight set heading bug, engage autopilot, select HDG mode.

attachment.php


BUG REPORT
Issue Experienced: Cockpit side window doesn't meet the framing on the lower edge.
Expected Behaviour: Should fill window.
Steps to Reproduce: View exterior of aircraft.
attachment.php


BUG REPORT
Issue Experienced: Right hand float switch not animated.
Expected Behaviour: Switch should move when clicked as the left hand one does.
Steps to Reproduce: Cycle float switches.

attachment.php


Nothing major and I'm sure you're already aware of it.
Click to expand...

THANKYOU! ❤️❤️❤️❤️❤️
For being the only person to use the bug report format! Please report to our discord for Test Pilot status 

Added to our Trello: https://trello.com/b/XrxlAg94/grumman-goose
 
Last edited:
I actually had to remove the Goose again from my Community folder since I have no clue as to how MSFS handles the AI aircraft at this point and while I generally believe you can't have too many round engines on any airport.....my PC disagreed and I had my first couple of CTDs :D

The Goose is not at fault of course....I just need a more powerful PC ;)

Cheers
Sunny
 
You must log in or register to reply here.
Back
Top